Eureka / Partition walls

The partition walls are made of panels with a length of 500, 750,
1000, 1250 o 1500 mm of the pitch between each vertical
element and a 250 mm module designed for technical
use and for bridging between other modules. They can have
a height of 2176, 2720 o 3264 mm and a depth of 100 mm.

Rails
The rails have a 60x32 mm U-shaped profile, and
are made from 1 mm-thick, zinc-coated, press-forged
steels sheet. They are supplied with a PVC foam gasket
to eliminate the transmission of noise and to compensate for
uneven ceilings and/or floors. The rails are installed using
screws and rawlplugs where possible, or with bi-adhesive
tape or silicone.

Vertical elements
The vertical elements have a 60x25 mm profile and
are entirely zinc-coated. They are made from 1.5 mm-thick
steel sheet with a series of 60x25 mm slots for laying
cables, and 5 mm holes every 32 mm for the 2 mm-thick,
zinc-coated, pressed-steel brackets for fixing
the horizontal elements in place and to locate the 54x5 mm
steel swivel pins used to fasten the panels.
Both the front and the back panels are supplied with
a PVC foam gasket so they adhere perfectly and to eliminate
the transmission of noise.
Adapters are available upon request to compensate
for any differences in height between the floor and ceiling,
up to a maximum of 70 mm.

Horizontal elements
The horizontal elements are made of 1.5 mm-thick,
zinc-coated, press-forged steel sheet with a 60x25 mm section.
They determine the length of the panels and are joined
to the vertical elements using 2 mm zinc-coated pressed
steel brackets fixed in place with self-tapping screws.
This system allows each single module to be easily
and quickly dismantled to change the layout of the system.
They are supplied with the same type of gasket as the
vertical elements.

Adjustment
The elements may be adjusted using levelling feet
with a stroke of +/- 20 mm inserted in the bottom
of the vertical elements.

Wiring system
The 60 mm space available in the wall and the slots
in the steel structure makes it easy to lay electric,
phone and data transmission cables both vertically
and horizontally.

Panels
All the panels are made of 18 mm-thick, class E1 melamine
chipboard (in compliance with current UNI/DIN Standards
on formaldehyde emissions), with a walnut, cream-white,
bleached oak-wood or silver-grey finish. The vertical edges
are trimmed with 1 mm-thick ABS with rounded edges,
and the horizontal edges are trimmed with 0.5 mm-thick ABS.

Fastening system
The panels are fastened in place with 1.5 mm-thick, zinccoated
steel brackets screwed to the internal face
of the panels, and steel swivel pins on the vertical elements.
Apart from being quick to install, this system allows for easy
dismantling and replacement of each single panel located
on the wall. It also guarantees a uniform 5 mm gap in both
the vertical and horizontal joints.

Upper and lateral bands
The upper and lateral bands allow the partition wall to be sealed
against the ceiling and the side walls starting with
a minimum of 75 mm. The maximum size may vary according
to the requirements of each project.

Base bands
Base bands made of melamine with the same finish
as the panels are available upon request. They are fixed
in place with high-carbon steel bronzed pressure clips.
This system allows for them to be easily removed if electric,
phone or data transmission wires need to be laid, even
on a completed wall.

Frame
The frame is made of extruded aluminium with an epoxy
powder paint finish, available in metallic silver-grey
or anodized silver, and a PVC gasket around the whole
perimeter. It is suitable for either single or double glass
windows, and may be supplied to site already assembled,
with a simple mechanism to fix it in place on the steel structure.

Window
The window may be supplied in either 6 mm-thick tempered
float or 3 +3 mm layered glass, in compliance with current
regulations. It may be either single or double, and the latter
may be supplied with an internal Venetian blind with
an electronic or manual control to open and close the blind.

Insulation
Upon request, the walls may be supplied with 60 mm-thick
wool-fibre insulating panels. The panels are non-toxic,
hypoallergenic, non-inflammable and non-hygroscopic,
and have a density of 22.

DOORS

Frame
The frame is made of extruded aluminium with an epoxy
powder painted finish in metal silver-grey, with a gasket
around the whole perimeter.

Solid door panel
The perimeter door panel is made of extruded aluminium,
with the same finish as the weight bearing frame, and of
melamine panels with the same finishes as the panelling.

Glass door panel
The glass door panel is supplied with the same structure
as the door panel, completed with two 6 mm-thick security
glass panels.

Higes
All the doors are supplied with three hinges in a satin aluminium
finish, fixed to the aluminium borders of the two frames.

Handle
Traditional handle with satin aluminium finish supplied
with a lock, fixed to the aluminium frame of the door panel.
The frames may also be fitted with “push and open” handles
upon request.

Door opening
The opening of the door is 865x2110 mm.
The height can be modified upon request by the client.

The open space wall is supplied with doors only
with the 2179 mm modules.