Eureka / Open space partitions

The open space partitions are made of panels with a length
of 500, 600, 800 or 1000 mm of the pitch between each
vertical element. The height can be of 899, 1091, 1635, 1859
or 2179 mm and depth of 100 mm.

Vertical elements
The vertical elements have a 60x25 mm profile and are
entirely zinc-coated. They are made from 1.5 mm-thick steel
sheet with a series of 60x25 mm slots for laying cables,
and 5 mm holes every 32 mm for the 2 mm-thick,
zinc-coated, pressed-steel brackets for fixing the horizontal
elements in place and to locate the 5x45 mm steel swivel
pins used to fasten the panels. Both the front and
the back panels are supplied with a PVC foam gasket so they
adhere perfectly and to eliminate the transmission of noise.
Adapters are available upon request to compensate
for any differences in height between the floor and ceiling,
up to a maximum of 70 mm.

Horizontal elements
The horizontal elements are made of 1.5 mm-thick, zinc-coated,
press-forged steel sheet with a 60x25 mm section.
They determine the width of the modules and are joined
to the vertical elements using 2 mm zinc-coated pressed
steel brackets fixed in place with self-tapping screws.
This system allows each single module to be easily
and quickly dismantled to change the layout of the system.
They are supplied with the same type of gasket
as the vertical elements.

Adjustment
The elements may be adjusted using levelling feet with
a stroke of +/- 20 mm inserted in the bottom of the vertical
elements.

Wiring system
The 60 mm space available in the wall and the slots
in the steel structure makes it easy to lay electric,
phone and data transmission cables both vertically
and horizontally.

Panels
The panels are made of 18 mm-thick class E1 melamine
chipboard (in compliance with current UNI/DIN Standards
on formaldehyde emissions) in a walnut, cream-white,
bleached oak-wood or silver-grey finish oak-wood. They are
also available in cherry-wood, bleached ash, smoked ash or
oak stained in dark walnut. The panels may also be supplied
with a fabric finish upon request.

Fastening system
The panels are fastened in place with 1.5 mm-thick,
zinc-coated steel brackets screwed to the internal face
of the panels, and steel swivel pins on the vertical elements.
Apart from being quick to install, this system allows for easy
dismantling and replacement of each single panel located
on the wall. It also guarantees a uniform 5 mm gap in both
the vertical and horizontal joints.

Wiring panel
The wiring panel is made of 18 mm-thick melamine
chipboard in the same finishes as the panels.
It is trimmed on three sides with 0.5 mm-thick ABS,
while the fourth side has a PVC co-extruded soft/rigid
profile to allow cables to be laid. The panel opens
with hinges fastened to the horizontal element to allow
easier access to the plugs.

Base bands
Base bands made of melamine in the same finish
as the panels are available upon request. They are fixed
in place with high-carbon steel bronzed pressure clips.
This system allows for easy removal if electric,
phone or data transmission wires need to be laid, even
on a completed wall.

Frame
The frame is made of extruded aluminium with
an epoxy powder paint finish, available in metallic silver-grey
or anodized silver, and a PVC gasket around the whole
perimeter. It is suitable for either single or double
glass windows, and may be supplied to site already
assembled, with a simple mechanism to fix it in place
on the steel structure.

Window
The window may be supplied in either 6 mm-thick
tempered float or 3+3 mm layered glass, in compliance
with current regulations. It may be either single
or double, and the latter may be supplied with an internal
Venetian blind with an electronic or manual control
to open and close the blind.

Closing profiles
The closing profiles are made of extruded steel
with an epoxy powder painted finish, in metal silver-grey
or anodized silver.

Corner connectors
The connectors comprise an aluminium pipe
with an epoxy powder painted finish in metal
silver-grey or anodized silver, that can be joined by two
to four corner connectors. This system allows
2, 3 or 4 cornersto be easily created in various layouts.